Catalogue of components

Adjustable flashing

Adjustable flashing - 4 types: for roof pitch 0-10°, 10-28°, 28-38°a 38-52°.


Bottom plate with round basic element

Bottom plate with round basic element, 1000mm, cutable.


CD – Cleanout door

It is set in chimney cladding in the place of cleaning - CVC chimney breeze block. [...]

The door is dual, metal and provided with powder coating of white colour.

Door measurements are 310x180mm (inside).

For the whole chimney kit, there is a revision tag, which is glued on the chimney door. as part of the system. This tag is designated for recording information about the chimney, for individual inspections by chimney foremen and by revision technicians


CDGAS – Chimney doors GAS

It is set in chimney cladding in the place of revision piece RRT. [...]

The door is metal and provided with powder coating of white colour. Door measurements are 310x180mm (inside).

For the whole chimney kit, there is a revision tag, which is glued on the chimney door. as part of the system. This tag is designated for recording information about the chimney, for individual inspections by chimney foremen and by revision technicians.


CDK, CDK2 – Cantilever plate

It is made of reinforced concrete, designated for section above roof, it is ready for walling. [...]

Plate is set in bed mortar on chimney body.

Types: 
CDK – for walling one-vent chimneys – measurements: 700mm x 700mm x 80 mm
CDK2 – for walling two-vent chimneys – measurements: 700mm x 545mm x 80 mm


CDO – Cover plate for walling

All cover plates are made of glass concrete in natural colour. [...]

Cover plates are set onto typical sack lime-cement mortar e.g. Multibat, to the last ceramic breeze block. When applying mortar, it is necessary to make sure that corner triangular holes in ceramic breeze block stay free of mortar. Cover plate is designated for walling above roof.

Measurements: 
length ………… 770 mm
width ………… 770 mm
height ………… 50 mm


CDO2 – Cover plate for two-vent chimneys

All cover plates are made of glass concrete in natural colour. [...]

Cover plates are set onto typical sack lime-cement mortar e.g. Multibat, to last ceramic breeze block. When applying mortar, it is necessary to make sure that corner triangular holes in ceramic breeze block stay free of mortar. Two-vent cover plates are designated for finishing off two-vent chimneys, for various types of sections above roof.

Measurements:
1170mm x 770mm x 50mm


CDT – Chimney doors TEC

It is set in chimney cladding in the place of cleaning - OT chimney breeze block closed with OUK or OUC. [...]

The door is metal and provided with powder coating of white colour.

Door measurements are 250x250mm.

For the whole chimney kit, there is a revision tag, which is glued on the chimney door. as part of the system. This tag is designated for recording information about the chimney, for individual inspections by chimney foremen and by revision technicians.


CDZ – Basic cover plate

All cover plates are made of glass concrete in natural colour. [...]

Cover plates are set onto typical sack lime-cement mortar e.g. Multibat, to last ceramic breeze block. During application of mortar, it is necessary to make sure that corner triangular holes in ceramic breeze block stay free of mortar. Basic cover plate is designated for plastered section above roof, it is ready for siding with facing bands, above roof chimney casing and component Komfort.

CDZ is universal for all diameters of internal flue liners.

Measurements: 
length ………. 560 mm
width ………. 560 mm
height ………. 50 mm


CDZ2 – Cover plate for two-vent chimneys

All cover plates are made of glass concrete in natural colour. [...]

Cover plates are set onto typical sack lime-cement mortar e.g. Multibat, to last ceramic breeze block. During application of mortar, it is necessary to make sure that corner triangular holes in ceramic breeze block stay free of mortar. Two-vent cover plates are designated for finishing off two-vent chimneys, for various types in section above roof level.

Measurements:
940mm x 540mm x 50mm


CDZT, CDOT – Cover plate with air intake

All cover plates are made of glass concrete in natural colour and metal profile. [...]

Cover plate is set onto above roof part using screwed asembly. Basic cover plate CDZT is designated for plastered section above roof, it is ready for siding with facing bands, above roof chimney casing and component Komfort. CDOT is designated for walled above roof part. CDZT and CDOT are universal for all diameters of internal flue liners. Can be used also for system CIKO GAS.

Measurements:
length ………. 540 mm (CDOT: 770 mm)
width ………. 540 mm (CDOT: 770 mm)
height ………. 50 mm


Ceiling exeution (atypical part)


CHG – Chimney exhaust cap

It is used for termination of plastic chimney flue liners of CIKO GAS system. [...]

Supplied measurements Ø80mm, 110mm, 125mm and 160mm


CHH – Historical chimney head

This variety of chimney cap is typical for some regions in Czech Republic. [...]

Made from glass concrete.

Dimesions: 420x420mm, Height: 300mm.


CHV – Head for rider dict

Head for rider dict is used for ending of installation and vent shaft.


CIB – Heat insulation

It guarantees excellent heat properties of a chimney system. [...]

It enables quick response of the chimney to heating-up and thus increases efficiency of the heating appliance. It also enables dilatation of a chimney vent from chimney cladding. It is made of high quality mineral fibres of volume weight 90 kg.m-3.
It is supplied in circle sectors that are equipped with a lock and make solid insulation layer.

Measurements: 
CIB 14 – thickness 60 mm, height 500 mm


CIRS – Heat insulation

It is supplied in cut matting and after installation creates integral insulation layer around inner refractory liner. [...]

It guarantees excellent heat properties of chimney system. It enables quick response of the chimney to heating-up and thus increases efficiency of the heating appliance. It also enables dilatation of a chimney vent from chimney cladding. It is made of high quality mineral fibres of volume weight 90 kg.m-3.
Measurements: 
CIRS 20 – thickness 30 mm, height 500 mm
CIRS 18 – thickness 40 mm, height 500 mm
CIRS 16 – thickness 50 mm, height 500 mm


CIT – Heat insulation TEC

Special design of heat insulation allows also air intake for the appliance.


CJ – Condensation drain

It is designated for fitting internal refractory flue liner and solves outlet of condensate. [...]

It is made of high quality acid-resisting ceramic. It is placed in chimney footing and it is outfitted with stainless tube 012 x 1 for outlet of condensate into a tumbler made of technic glass.
Measurements :

internal diameter
200mm – CJ20
180mm – CJ18
160mm – CJ16
140mm – CJ14

height – 70 mm


CK – Chimney cap

It improves technical and aesthetical characteristics of the chimney, it is delivered as one piece together with a chimney collar. [...]

It prevents rainwater from getting inside insulation as well as into chimney vent. It is made of grey cast iron and is provided with dark polyurethane paint for cast iron. It is glued to the last chimney flue liner by refractory glue that is the same as the one used for other flue liners. Its lifetime is unlimited.

Types: 
CK 20 – for internal diameter of flue liner 200mm
CK 18 – for internal diameter of flue liner 180mm
CK 16 – for internal diameter of flue liner 160mm
CK 14 – for internal diameter of flue liner 140mm


CKMB – Mortar

Mortar for mason of chimney body from CU and CT bricks.


CKOP – Crown rings Komfort

Exposed rings, that imitate face walling, are used for above roof level component Komfort. [...]

In this case, breeze blocks are not used for external cladding in the section above roof. Material used for rings is coloured and therefore a long-term colour constancy is guaranteed. Adhesive material Komfort CKOL is supplied for glueing rings; reinforcement kit CKOV is supplied for reinforcement of the section above roof.

Types:
CKOP – rings for one-vent chimneys
CKOP II – rings for two-vent chimneys

Rings are universal for all types and diameters of CIKO chimneys.


CKOPB – Crown rings Komfort white

Exposed rings, that imitate face walling, are used for above roof level component Komfort. [...]

In this case, breeze blocks are not used for external cladding in the section above roof. Material used for rings is coloured and therefore a long-term colour constancy is guaranteed. Adhesive material Komfort CKOL is supplied for glueing rings; reinforcement kit CKOV is supplied for reinforcement of the section above roof.

Types:
CKOPB – rings for one-vent chimneys
CKOPB II – rings for two-vent chimneys

Rings are universal for all types and diameters of CIKO chimneys.


CKOPC – prstence hlavy Komfort černé

Pro nadstřešní část Komfort jsou použity černé pohledové prstence, které imitují hlavu komína z lícových cihel. [...]

V nadstřešní části se v tomto případě již nepoužívají tvarovky obvodového pláště. Prstence jsou probarveny ve hmotě a tudíž je zaručena dlouhodobá barevná stálost. Pro lepení prstenců je dodávaná lepící hmota Komfort CKOL a pro vyztužení této nadstřešní části pak zálivková směs CZS. Při nadstřešní části vyšší než 1,5 metru doporučujeme vyztužení pomocí sady výztuže CKOV.

Typy:
CKOPC – černé prstence pro jednoprůduchové komíny
CKOPC2 – černé prstence pro dvojprůduchové komíny

Prstence jsou univerzální pro všechny typy i průměry komínů CIKO.


CKOPH – prstence hlavy Komfort hnědé

Pro nadstřešní část Komfort jsou použity hnědé pohledové prstence, které imitují hlavu komína z lícových cihel. [...]

V nadstřešní části se v tomto případě již nepoužívají tvarovky obvodového pláště. Prstence jsou probarveny ve hmotě a tudíž je zaručena dlouhodobá barevná stálost. Pro lepení prstenců je dodávaná lepící hmota Komfort CKOL a pro vyztužení této nadstřešní části pak zálivková směs CZS. Při nadstřešní části vyšší než 1,5 metru doporučujeme vyztužení pomocí sady výztuže CKOV.

Typy:
CKOPH – hnědé prstence pro jednoprůduchové komíny
CKOPH2 – hnědé prstence pro dvojprůduchové komíny

Prstence jsou univerzální pro všechny typy i průměry komínů CIKO.


CKP – Chimney footing

Chimney footing is made of bulk concrete of strength C16/20 and breeze blocks. [...]

Its structure enables air distribution to all openings of rear ventilation of chimney body. At the same time, there is outlet of condensate, from refractory condensate drain, that is set in chimney footing. Condensate trickles down in a tumbler made of technic glass. Air grate is set on flexible adhesive after chimney plastering is finished.

Measurements: 
length …………. 400 mm
width …………. 400 mm
height …………. 250 mm
weight ………….. 44 kg


CL – Chimney flashing

It provides termination of a chimney vent and prevents rainwater from getting inside insulation of the chimney. [...]

It is made of ceramic and is provided with dark enamel. It is glued to the last chimney flue liner by refractory glue that is the same as the one used for other flue liners. Its lifetime is unlimited.

Types: 
CL 20 – for internal diameter of flue liner 200mm
CL 18 – for internal diameter of flue liner 180mm
CL 16 – for internal diameter of flue liner 160mm
CL 14 – for internal diameter of flue liner 140mm


CM – Air grate

Air grate provides sufficient inflow of air into air vents of the chimney body. [...]

It also enables inspection and possible pouring out of build-up condensate from the tumbler.

Air grate including frame is made of metal and measurements are 120mm x 120 mm.

Air grate is provided with powder coating of white colour.

Air grate is laid in finished plaster in the chimney base. Grate frame is glued with flexible adhesive and it is tightly set in the chimney footing. The grate is removable.


CNNB – Chimney wrap above roof STUKO

Chimney wraps in section above roof serve as protection of chimney section above roof against weather impact. [...]

Before installation, the chimney wraps must be trimmed according to the height of chimney section above roof and according to the roof sloping.

Measurements:
CNNB – width 420mm, length 420mm, height 1000mm; 1250mm; 1700mm; 2000mm

Weight:
CNNB – 10kg/ 1m’


CNNC – Chimney wrap above roof IMIT

This variant of chimney wrap looks like imitation masonry for chimney part above roof. [...]

Chimney wraps in section above roof serve as protection of chimney section above roof against weather impact. Before installation, the chimney wraps must be trimmed according to the height of chimney section above roof and according to the roof sloping.

Measurements: 
CNNC – width 450mm, length 450mm, height 1000mm; 1250mm; 1700mm

Weight:
CNNC – 40kg/ 1m’


CS – Tumbler for condensate

Tumbler is made of acid-resisting technic glass and it is placed behind the air grate, inside footing of the chimney ( measurements 60x60 mm). [...]

It serves as a collecting place for build-up condensate in the chimney body.


CSHS – Jointing material

Jointing material is used for glueing refractory flue liners. [...]

It is supplied in optimal consistency and no other thinning is necessary.
It is applied into half-groove in lower refractory flue liner. When upper flue liner is set, the squeezed material is wiped off so that the created join is even and smooth without gaps and protrusions.

Measurements: 
package …… 3 kg

spreading rate:
Ø 140mm …… 7m´
Ø 160mm …… 6m´
Ø 200mm …… 4,5m´


CSN – Chimney hood – Napoleon

Chimney hood, or NAPOLEON, is made from copper or stainless sheet metal. [...]

It prevents rainwater from entering the chimney vent. It is anchored with special anchors attached to additional air holes of last layer of chimney breeze blocks. Before fastening Napoleon, it is necessary to drill holes into cover plate for anchors according to enclosed assembly instructions.

It is made in two variants:
CSN-NER – Napoleon for one-vent chimneys from stainless sheet metal
CSNII-NER – Napoleon for two-vent chimneys from stainless sheet metal
CSN-CU – Napoleon for one-vent chimneys from copper sheet metal
CSNII-CU – Napoleon for two-vent chimneys from copper sheet metal

Napoleon is the same for all diameters and types of vents.


CT – Connecting chimney breeze block

Ceramic burnt breeze block is made of brick clay designated for multi-vent chimneys. [...]

Its construction ensures interconnection of individual chimney bodies. These breeze blocks are used in combination with typical breeze blocks of chimney cladding (CU) in every second masonry layer. Typical masonry bond that will ensure static collaboration of whole chimney cladding is created in this way.

Measurements:
length ……………………………………………… 390 mm
width ……………………………………………… 220 mm
height ……………………………………………… 250 mm
weight of one breeze block ………….…………… 9 kg


CU – Chimney breeze block

Breeze block of chimney cladding is made of brick burnt clay and it is designated for walling CIKO system chimney cladding. [...]

Breeze blocks are laid in pairs in each layer, they are turned by 90° in individual layers. By this way is created typical masonry bond that will ensure static reliability of the construction. breeze blocks for various diameters and types of vents are identical and they vary only in thickness of insulation or the type of internal flue liners.

Compression strength: min. 10 Mpa
Volume weight: 600 ±100 kg.m-3
Measurements: 
length ……………………………………………… 400 mm
width ……………………………………………… 196 mm
height ……………………………………………… 250 mm
weight of one breeze block ………..……………… 9,5 kg
Cross-section measurements of one vent chimney: 400mm x 400mm
Cross-section measurements of two vent chimney: 400mm x 800mm etc.


CV – Flue liners basic

Ceramic flue liners are made of high quality ceramic. [...]

They are resistant to high temperatures and temperature changes, they have unlimited lifetime, are resistant to flue gases, burn through and acidic condensate, have low absorbing capacity, are gas-tight and have high dimension precision. All properties comply with ČSN EN 1457. Liners are provided with half-groove through which they are cemented with jointing material CSH.

Measurements:
CV20 – internal Ø200mm, height 328mm, liner thickness 15mm
CV18 – internal Ø180mm, height 328mm, liner thickness 15mm
CV16 – internal Ø160mm, height 328mm, liner thickness 15mm
CV14 – internal Ø140mm, height 328mm, liner thickness 15mm

Characteristics of ceramic fireclay refractory liners:
Pressure resilience: 47,7Mpa
Absorbability: 8,7%
Volume weight: 2092 kg.m-3
Resilience to acidity: 0,47%
Right temperature of waste gases: < 600 C°
Resistance to soot burn out: > 1000 C°
Gastightness : after operating phase when p=40Pa leakage 13,13 l.s-1.m-2


CVC – Chimney breeze block for cleaning

It is set in place of required opening for cleaning. [...]

It has same technical properties as basic flue liners.

Measurements :
CVC 20 – internal diameter 200 mm
CVC 18 – internal diameter 180 mm
CVC 16 – internal diameter 160 mm
CVC 14 – internal diameter 140 mm

height
660 mm – all types are same

opening for cleaning
130x260mm – all types are same


CVK – Chimney flue liner – connecting flue tee 45°

Chimney breeze block connecting smoke flue to a vent in angle of 45°. [...]

Internal diameter of connection is the same as diameter of the vent. It has same technical properties as basic flue liners.

Measurements : 
CVK 20 – internal diameter 200 mm, diameter of connection 200mm
CVK 18 – internal diameter 180 mm, diameter of connection 180mm
CVK 16 – internal diameter 160 mm, diameter of connection 160mm

Height
660 mm


CVS – Chimney flue liner – connecting flue tee 90°

Chimney breeze block for connecting smoke flue. [...]

Internal diameter of connection is same as diameter of the vent. It has same technical properties as basic flue liners.

Measurements:
CVS 20 – internal diameter 200 mm, diameter of connection 200mm
CVS 18 – internal diameter 180 mm, diameter of connection 180mm
CVS 16 – internal diameter 160 mm, diameter of connection 160mm
CVS 14 – internal diameter 140 mm, diameter of connection 140mm

height
660 mm – all types have same height


CZS – Grout for chimney head

CZS grout is used for static reinforcement of above roof part and chimney body. [...]

Primary for CKOP a CKOPB


Foundation element

Non-variable


Inspection lenght – high temperature


KBD – Dummy cover


KD – chimney door PRAKTIK


KJ – Condensate collector with drain


KK – rain cap


KL – Ukončovací prvek PRAKTIK s límcem

Ukončovací prvek PRAKTIK s límcem umožňuje zadní odvětrání komínového tělesa a zároveň zabraňuje zatékání vody do izolace. [...]

Na poslední komínovou vložku, těsně na horní lem krycí desky, se upevní komínový límec (spoj doporučuje podsilikonovat nehořlavým silikonem). Krycí deska tak společně s límcem zabraňují zatékání vody do komínového tělesa a zároveň umožňují jeho zadní odvětrání, které je důležité především pro bezpečnost komínu ve stavbě.  Pro průměry 130 a 160mm je součástí distanční prvek, který se lepí ke krycí desce ještě před instalací límce. Dodáváno pro průměry 130, 160, 180, 200mm.

Materiál: nerezová ocel


KT – single-gasket

max. 200°C


KV – Insulated stainless steel flue liner with wall distancers


KVC – high-temperature inspection hatch


KVCP – Inspection lenght round cap, max. 200°C

Natural gas


KVK – Insulated T45° high temperature


KVS – Insulated T90° high temperature


KZP – base element PRAKTIK


Lenght

Delivered in diameters 113, 130, 150, 160, 180, 200, 250 a 300 mm. [...]

Lenght  – 360, 540, 1080mm.


Locking band


ODO – Spacer socket

Used for stabilisation of flue liners in chimney body (without insulation).


OKJ – Condenzation basin TEC


OS – cleaning chimney T-piece


OT – Diaphragm seal for gas appliance


OUC – inspection door TEC

Inspection door TEC for solid fuel appliance. Up to 450°C.


OUK – inspecion door TEC

For gas appliances. [...]

Gas-tight closure of the vent stack for over-pressure operation.


OV – flue liner TEC

Flue liners TEC are made by special technology of isostatic press and are suitable for exhaust of flue gases from appliances running on all kinds of fuel with natural or forced exhaust of flue gases. [...]

Isostatic neck flue liners – lenght 660mm, dimesions 140, 160, 180, 200mm.


R – Firm pipe

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

Assembly by means of bell-and-spigot joint with silicone gasket – transparent colour.

Measurements:
Ø 80mm, lengths 0,5m; 1,0m and 2,0m
Ø 110mm, lengths 0,5m; 1,0m and 2,0m
Ø 125mm, lengths 0,5m; 1,0m and 2,0m
Ø 160mm, lengths 0,5m; 1,0m and 2,0m


RA – adapter flue way – chimney

Made of highly resistant plastic, specified for exhaust of flue gases with maximum temperature of 120°C. [...]

It is used as a reducer for connecting flue way with chimney vent.

Supplied sizes:
Ventilation reducer from flue way 80mm to chimney vent 75mm diameter
Ventilation reducer from flue way 60mm to chimney vent 75mm diameter
Ventilation reducer from flue way 60mm to chimney vent 110mm diameter
Ventilation reducer from flue way 75mm to chimney vent 110mm diameter
Ventilation reducer from flue way 80mm to chimney vent 110mm diameter
Ventilation reducer from flue way 60mm to chimney vent 110mm diameter
Ventilation reducer from flue way 75mm to chimney vent 125mm diameter
Ventilation reducer from flue way 80mm to chimney vent 125mm diameter
Ventilation reducer from flue way 110mm to chimney vent 125mm diameter
Ventilation reducer from flue way 60mm to chimney vent 160mm diameter
Ventilation reducer from flue way 75mm to chimney vent 160mm diameter
Ventilation reducer from flue way 80mm to chimney vent 160mm diameter
Ventilation reducer from flue way 110mm to chimney vent 160mm diameter
Ventilation reducer from flue way 125mm to chimney vent 160mm diameter


Rain cap


Rain collar


RDO – Distance ring flexible

It is used for horizontal stability of plastic flue liners inside chimney vent. [...]

It is used throughout the whole chimney.

Supplied measurements Ø80mm, 110mm, 125mm, 160mm.


RF – Flexible pipe

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

Used mostly for additional chimney flue lining – black colour.

Measurements:
Ø 75mm, lengths 1,0m to 25m
– supplied in any length in mb.
Ø 110mm, lengths 1,0m to 25m
– supplied in any length in mb.
Ø 125mm, lengths 1,0m to 20m
– supplied in any length in mb.


RFF – Reducer flexible/flexible

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

It is used for connecting two flexible pipes – black colour.

Supplied measurements Ø75mm, 110mm, 125mm.


RFP – Reducer flexible/firm

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

It is used as a reducer from flexible to firm pipe system – meaning from the bottom (along with flow of flue gases) – black colour.

Supplied measurements Ø 75mm, 75/80mm, 110mm, 125mm


RK – Elbow bend 87,5°

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

Chimney breeze block connecting smoke flue to a vent in angle of 45°. Internal diameter of connection is the same as diameter of the vent. It has same technical properties as basic flue liners.
It connects smoke flue on boiler side in angle of 87,5°, where there is outlet of condensate within the boiler and not within the chimney vent – for example condensing boilers.

Supplied measurements Ø 80mm, 110mm, 125mm and 160 mm.


RK45 – Elbow bend 45°

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

It connects smoke flue on boiler side in angle of 45°, where there is outlet of condensate within the boiler and not within the chimney vent – for example condensing boilers.

Supplied measurements Ø80mm, 110mm, 125mm and 160mm.


RKD – insert for CIKO GAS with UV stabilisation


RNO – Fastening ring

It is used as a fastening and attaching component for first and last section of plastic flue liners inside chimney vent.


RPF – Reducer firm/flexible

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

It is used as a reducer from firm to flexible pipe system – meaning from the bottom (along with flow of flue gases) – black colour.

Supplied measurements Ø 75mm, 80/75mm, 110mm, 125mm and 160mm.


RR – Revision cap


RRK – Revision cap with condensate outlet

It is used as a door for inspection of a chimney vent. [...]

Part of this opening is a cap for outlet of condensate.

Supplied measurements Ø80mm, 110mm and 125mm, 160mm.


RRT – revision piece

It is used as a door for inspection of a chimney vent. [...]

Supplied measurements Ø 80mm, 110mm, 125mm and 160mm


RT – T-piece

Made of highly resistant plastic designated for exhaust of flue gases, maximum temperature is 120°C. [...]

It connects smoke flue on boiler side or optionally it serves as a door for inspection.

Supplied measurements Ø 80mm, 110mm, 125mm and 160mm.


T-90° high temperature


Wand band

Wand band - distance 50 - 400 mm.